F-Secure User Guides

Looking for:

Windows server 2012 standard support memory free

Click here to Download

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
I read on Microsoft’s website Here, that the physical memory limits for a x64 server R2 Standard machine is 4TB. replace.me › blog › memory-limits-and-editions-of-windowsan.
 
 

 

Windows server 2012 standard support memory free

 

In this case, we can purchase either 50 CAL licenses to cover the 50 users we have or alternatively 25 DAL licenses to cover the total amount of workstations that need to access the server.

In this scenario, purchasing DALs is a more cost effective solution. If however we had 10 users with a total of 20 devices , e. Windows Server Foundation is available to OEMs Original Equipment Manufacturers only and therefore can only be purchased at the time of purchasing a n new hardware server. Windows Foundation edition supports up to 15 users. In addition, Foundation edition owners cannot upgrade to other editions.

The Essential edition of server is available to OEMs with the purchase of new hardware and also at retail stores. The user limit of this server edition is 25 and device limit is This means that a maximum of 25 users amongst 50 computers can access the Windows Server Essentials edition. For example, you have 20 users rotating randomly amongst 25 computers accessing the Server Essentials edition, without any problem. A common question at this point is what if the organization expands and increases its users and computers?

In these cases Microsoft provides an upgrade path allowing organizations to upgrade to the Windows Server Standard or Datacenter edition license and perform an in-place license transition. Once the transition is complete, the user limitation, and other features are unlocked without requiring migration or reinstallation of the server. Companies upgrading to a higher edition of Windows Server should keep in mind that it will be necessary to purchase the required amount of CALs or DALs according to their users or devices.

Administrators will be happy to know that it is also possible to downgrade the Standard edition of Server to the Essentials edition. For example, it is possible to run Essential edition of Server as virtual machine utilizing one of two available virtual instances in Standard edition as shown in the figure below.

This eliminates the needs to purchase Essential edition of Server Download Now! Unlike Windows Server Essentials non-R2 , you can now run a single instance of a virtual machine. The server licensing rights have been expanded, allowing you to install an instance of Essentials on your physical server to run the Hyper-V role with none of the other roles and features of the Essentials Experience installed , and a second instance of Essentials as a virtual machine VM on that same server with all the Essentials Experience roles and features.

Definition of a socket is a CPU or physical processor. Logical cores are not counted as sockets. A single license of Standard and Datacenter edition covers up to two physical processors per physical server. Standard edition allows up to 2 virtual instances while the Datacenter edition allows unlimited number of virtual instances.

For example, a Windows Server R2 Standard edition installed on a physical server with one socket CPU can support up to two instances of virtual machines. These virtual machines can be Server R2 Standard or Essentials edition. Similarly, if you install a Windows Server R2 Datacenter edition , then you can install an unlimited number of virtual machines.

Scenario 2 : Install Server Standard Edition on a physical server with 1 physical processor, running 8 instances of virtual machines. A total of 50 users will be accessing the server. Remember that a single Standard edition license covers up to two physical processors and up to two instances of virtual machines.

Since the requirement is to run 8 instances of virtual machines, we need four Standard edition licenses. If we decided to use the Datacenter edition in this scenario, a single license with 50 CAL would be enough to cover our needs, because the Datacenter edition license supports an unlimited number of virtual instances and up to two physical processors. Back to Windows Server Section. Read more. Click Activate Windows.

After security hardening, the administrator account changes from administrator to SWMaster. When you install the operating system, a host name is generated by default. To facilitate server management, you are advised to change the host name based on the plan.

Procedure Start the installation program. On the toolbar of the Remote Virtual Console , click to set the installation media. Set the boot item. On the iBMC web management page, choose Configuration from the main menu. In the navigation tree on the left, choose Boot Device. Set the parameters listed in the following table. If the server is H V5 and the Windows installation disc does not contain the corresponding driver, perform the following operations to load the driver: On the toolbar of the Remote Virtual Console , click and click Disconnect to disconnect the inserted system disk.

Select Directory , click Browse , and select a driver decompression directory. Click Connect. Click Load driver. Click Next to install the driver.

After the installation is complete, the storage device is displayed. On the toolbar of the Remote Virtual Console , click and click Disconnect to disconnect the inserted driver disk. Insert the system disk and click Connect to continue installing the operating system. Verification Log in to the eSight server as the Administrator user.

Right-click Computer and choose Properties from the shortcut menu. Turning Off the Windows Operating System Firewall After the operating system is installed, the firewall is enabled by default. Procedure Log in to the server as the Administrator user. Click Turn Windows Firewall on or off. Configuring the Network After the operating system is installed, you must configure the network to connect the eSight server to the network.

Click Network and Sharing Center. Click Change adapter settings. Double-click a network connection whose IP address you want to set, for example, Local Area Connection. Click Properties. Set the IP address. Click Use the following IP address. Click OK. Click Use the following IPv6 address. Verification Log in to another computer that can communicate with the network where the eSight server resides. Enter cmd and click OK. The CLI is displayed. Enter ping eSight server IP address and press Enter.

Configuring the Windows Remote Desktop If you want to connect to the eSight server through the remote desktop for eSight maintenance, configure the remote desktop. Prerequisites The firewall has been disabled. Procedure Log in to the server as the administrator user. Right-click Computer and choose Properties. Click Remote settings. Click the Remote tab and select an option under Remote Desktop as required.

Enter mstsc and click OK. Enter the eSight server IP address and click Connect. Select a login account, enter the password, and click OK. Click Yes. Setting the Virtual Memory If the default system settings are used, the virtual memory paging file may be too large. In the System window, click Advanced system settings. In the System Properties dialog box, click the Advanced tab and click Settings in the Performance area.

In the Performance Options dialog box, click the Advanced tab and click Change in the Virtual memory area. Set the virtual memory of the system drive C:. Activating Windows To ensure normal use of eSight, you are advised to activate the Windows operating system within 90 days. Prerequisites You have obtained the product key of the Windows Server R2 standard edition. Context The Windows Server R2 standard edition can be activated online or through a call. Verification Log in to the server as the administrator user.

In the System windows, check Windows activation information. Optional Changing the Operating System Host Name When you install the operating system, a host name is generated by default. Procedure Log in to the operating system as the SWMaster user.